1985-On 700R4 Humvee Special. Swap a TH400 3 Speed to a 700R4 4 Speed Overdrive Transmission.
Convert your TH400 transmission to a 700R4 overdrive transmission. You get the level 2, 700 Raptor Junior transmission, #2 special low stall diesel torque converter, special low RPM diesel governor, special adapter and special output shaft #50-6901, Beast shell upgrade, dip stick, throttle valve cable / bracket / stud, 8 Red Eagle clutches and full thickness Kolene steels in the 3-4 clutch drum, full throttle 3-4 up-shift sleeve, special Humvee to 700R4 flexplate and a plastic dust cover. This is an easy conversion, reuse your transfer case and drive shafts as they are now. Get a 30 to 40% increase in mileage and 30% lower motor speed. If you had a top speed of 70 MPH before, it will have a top speed of 90 to 100 MPH now. You get all of this plus no core charge.
SUBJECT: Proper installation of the throttle valve cable on Factory and after-market carburetors or fuel injections. This information applies to all 700R4, 4L60 and 200-4R transmissions. Throttle valve cable adjustment instructions, numbers 4, 5 and 6.
#1. The button that the cable hooks to at the carburetor or throttle body must have approximately 1 and 3/32-inch radius from the center of the throttle shaft to the center of the button the cable hooks to.
#2. Looking at the throttle shaft lever from the left side at idle position, approximately 33% of the throttle lever total travel must be to the rear of the throttle shaft centerline. And at wide-open throttle, approximately 67% to the front of the throttle shaft centerline. This will be about ½-inch to the rear and 1 inch to the front of the throttle shaft centerline.
#3. The throttle valve cable must be hooked up in this manner so the pressure will rise faster off idle and slow down at heavy throttle. If the pressure cable is pulled in a more even manner the pressure will be too low at light throttle. Failure to hook-up the throttle cable in this way will burn the three-four clutch pack up fast.
#4. The throttle valve cable controls transmission pressure. Adjusting this cable is the most important step when installing a 700R4, 4L60 or 200-4R transmission.
#5. The final step is to adjust the throttle valve cable. The cable must be adjusted so it is pulled fully out at wide-open throttle. To make sure disconnect the cable, hold the throttle wide open with your left hand, pull the cable fully out with your right hand and see if the cable end lines up with the button on the throttle lever. The cable should also be pulled out 3/8 to 1/2 of an inch at idle.
#6. Do not attempt to adjust the shift timing with the throttle valve cable. The shift timing is controlled by the governor springs and weights. For higher shift points at wide-open throttle install lighter springs. For lower shift points at wide-open throttle install stronger springs. After the cable is adjusted the approximate shift points should be 15 to 18, 25 to 30 and 40 to 50 MPH at very light throttle depending on tire size and axle ratio. Light throttle shift points are measured in MPH and full throttle shift points are measured at what RPM. The full throttle 1-2 shift will usually be at a higher RPM than the 2-3 shift. The governor will work with only 1 spring or 2 springs. You can remove one spring to raise the full throttle shift points.
#7. You can get a cable button off of a junk GM vehicle and weld it to your throttle valve lever. We sell a cable correction kit for Holley and Edelbrock carburetors.
#8. Sometimes on a newly rebuilt 700R4 or 200-4R transmission, it may not make the 3-4 shift when first installed. A stuck valve, trash in the fluid or an air pocket, usually causes this. Raise the rear wheels off the ground, place the transmission in overdrive position. Run the speedometer as high as 100 miles per hour, pop the throttle on and off and see if you can force a 3-4 shift. Once it makes the first 3-4 shift, work the shift lever back and forth between drive and overdrive until the 3-4 shift works correctly.
#9. If you have a Holley or Edelbrock carburetor, you must install an adapter on the carburetor linkage for the transmission to work correctly.
17 Days, 3 thousand miles, pavement, dust, rocks, sand, pain, relief, and joy. What else could you ask for?!?
May 3, 2006
Cole here, from Hummin2London. I bought your Quadzilla 4L80E and raced it in my H1 Hummer in Morocco last month. I was very happy with the gearbox and we took 4th in our class, even with two teenage boys strapped in the back. We had one major drama and that was the studs that screw into the back of the gearbox and hold the transmission mount / transfer case all backed out of the gearbox!!! ACKK!!!!
We pulled out the spacer / xfer case and retapped the holes to 10mm (no US thread bolts anywhere in Africa), new 10mm bolts, lots of loctite and a massive ratchet strap around the gearbox, crossmember and the back of the transfer case. We kept racing although a bit slower, and it all held together. I’m going to have to re-do those holes, probably Helicoils, unless you have any better ideas or suggestions.
Operationally the gearbox was fantastic! I am dead happy with it.
Scary Fast Hummer Racing (formerly Hummin2London)